| | Sector | abcWater Storage and Supply | Tender Value | INR 11.96 Lakhs approx. | | Location | Kerala - India | Ref.No | 86768723 | | Closing Date | 03 - Sep - 2025 | | | | Conversion of PHC to FHC Aardram works at Koruthodu, Civil works, Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation, trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil ,4.1.8, Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level148 (1 cement 4 coarse sand 8 graded stone aggregate 40 nominal size) ,50.6.1.6 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in CM 16 ( 1 cement 6 coarse sand sand) etc complete ,13.1.1 12 mm cement plaster of mix14 ( 1 cement 4 fine sand) ,13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shadeNew work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) ,16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade, made by block making machine with strong vibratory compaction, of approved size, design & shape, laid, in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the, joints with fine sand etc. all complete as per the direction of Engineer-in-charge. ,12.51.1, Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total, coated thickness, zinc coating 120 grams per sqm as per ISmm(+0.05%) total coated thickness, Zinc, coating 120 grams per sqm as per IS 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both, side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws, completeRidges plain (500-600 mm) ,10.16.1, Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including, cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding, and bolted with special shaped washers etc. complete.Hot finished welded type tubes ,21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately)For fixed portion Powder coated aluminum (minimum thickness of powder coating 50 micron) ,21.2.2 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS 12823 Grade I Type II, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides ,21.3.1, Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM, rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -, in -Charge. ( Cost of aluminum snap beading shall be paid in basic item)With float glass panes of 4.0, mm thickness ,od232942/2024_2025, Branding, Supplying and fixing signage charge including cost of creative designing, materials, labor, charges, conveyance, hire charges of scaffolding, making good the walls after work, all sundry expenses, etc complete. |
|
|
If you are a new user, then please
register, it's Free and then fill the form below.
If you are registered with us, just fill the form below, we will get back to you
shortly.
|
All fileds marked with '*' are compulsary.
|
|
|
|